How to remove plasti dip that won’t peel: Steps-by-Steps Guide

Plasti Dip is an excellent car accessory that comes in many colors and eliminates the need to hand-paint your car.

Plasti Dip can also be easily removed and reapplied. You can spray it on, remove the edge with your fingernail, then use a putty knife to remove the excess.

Plasti Dip must be removed, but you should remember a couple of things.

PLASTI DIP Rubber Coating Spray

Don’t use paint thinner or scraping tools to help you remove it whenever you want to wash your car because the chemicals may leave marks on your paint.

Using the WD-40 or dip remover that comes with Plasti Dip is recommended to remove it correctly.

Read more: Best Rattle Can Paint Job for Automative.

How do you remove hardened Plasti Dip?

how to remove plasti dip from wheels

One of the common issues associated with Plasti Dip protective coatings is peeling, which is completely understandable.

It may have been applied incorrectly, or the weather may have dried out the product. Peeling, whatever its cause, is a common phenomenon and certainly not a sign of failure.

To remove the coating in a single piece, gently pull the edges of the coating. If this does not work, you can use WD-40 or dip remover to slowly and carefully remove it. Do not rush this process.

What will dissolve Plasti Dip?

It was found that spraying WD-40 on the top of the Dip before removing the dip made the procedure of removing it easier.

Spraying WD-40 on the top of the Dip before removing the dip helped make the process easier.

This is also very useful for removing overspray, since it can be used to simply rub off the overspray as easily as it can be applied.

Does wd40 dissolve Plasti Dip?

WD-40 is an excellent product for removing dips that are stuck to surfaces. In addition to being grease-free, WD-40 will not stick to any oils, lubricants, or lubricant dips.

There are certain properties of the dip that make it easier to clean up overspray and get the dip out of tight places since it has properties that melt the dip away.

What’s The Easiest Way To Remove Thin Plasti Dip?

removing plasti dip easy

You’ll Need Listed Tool:

  • Jack
  • Jack stands
  • Automotive tape, if needed
  • Plastic sheeting, if needed
  • Microfiber towels
  • Impact wrench
  • Box cutter
  • Pressure washer
  • Dip Dissolver

Here’s a Guide to Removing Plasti Dip:

Peeling Plasti Dip

Your car should be able to easily be peeled off if it has been painted with multiple layers of Plasti Dipped. Otherwise, you’ll need to use another product.

  • In order for your car to cool off, you should park it in a shady area.
  • Plasti Dip should be applied to corners and edges of panels, doors, and hoods using a microfiber towel. Disturbing the dip and causing its edges to peel should achieve this result.
  • Remove a corner of the Plasti Dip from the panel by slowly peeling it off. The dip should come off in the same way it came on like vinyl.
  • Until all Plasti Dip has been removed, repeat steps 2 and 3.
  • Your car needs to be washed and waxed now.

Dissolving Plasti Dip

  • Removing the wheels and placing them in a safe place is a good idea if you are doing wheels.
  • Tape and plastic sheets should be used to protect black plastic or other trims on your body panels.
  • Ensure that the car is totally dry before using it.
  • Spray Dip Dissolver with a thin coat on a panel or area.
  • Set the dissolver in place and let it eat away at the dip.
  • If the dip is difficult to wipe away with your finger, wait a few minutes. You may notice some of it dripping. 
  • Clean the Plasti Dip away with a pressure washer. 
  • In case there is any remaining Plasti Dip, repeat steps 3-7.
  • You did a great job, now go get your car washed and waxed.

Frequently Asked Questions

Can you remove Plasti Dip with a pressure washer?

ways to remove plasti dip

People are hesitant to use pressure sprayers to wash cars that have been sprayed with Plasti Dip due to the ease at which it can be peeled off by hand.

In this case, you must allow the Plasti Dip to cure for several weeks after applying it correctly. Using a common water sprayer up to 1800 psi pressure won’t peel it along edges and across other areas.

Is WD-40 safe on car paint?

When applied to a car’s paint alone, WD-40 contains a number of products that are damaging to it. In spite of this, yes – this product is SAFE to use on paint due to the blend and combination of ingredients.

How Much Does it Cost to PlastiDip a Car?

If you’re doing it yourself, you’ll likely spend between $200-600, depending on how large your vehicle is. There may be a slight charge for pearls and fancy colors, and professional application of the Plasti Dip will, of course, increase labor costs. Depending on the size of your vehicle, labor costs may vary.

How do you remove Plasti dips from a steering wheel?

what takes plasti dip off

Wheels need to be removed from the car. Make sure you have kerosene on hand. After dipping your toothbrush in the kerosene, apply plasti dip to it. Wait for ten minutes.

Use a blunt stick to chip away the plasti dip while peeling it. You should then wash the remainder of the plasti dip with warm soapy water. Repeat steps 6 as needed and rinse until all of the plasti dip is clean.

What is the Best Way to Clean Plasti Dip?

You can really wash dipped components the same way you would if you were washing a car. Plasti Dip should not be exposed to strong chemicals or solvents such as gasoline as they cannot hold up to them.

If you wish to add an extra layer of protection to your Plasti Dip job, DYC offers Dip Armor. It is resistant to gasoline and may be topped with ceramic coatings.

Conclusion

Hopefully, our instructions on how to remove plasti dip from a car have been of help to you. If you purchased this adhesive and applied it, removal was probably the last thing on your mind.

That is, unless you became bored with it and decided you wanted it removed. This is not too difficult a process, and if you have the required equipment and the ability to follow simple instructions, you should have no problem doing this yourself.

In the future, keep in mind the removal process if you intend to purchase similar products for your vehicle.

When it comes to the amount of effort required for application and removal, you definitely don’t want to bite off more than you can chew.

Hopefully, now you know how to remove the adhesive if you decide to use it again.

Leave a Comment

Your email address will not be published. Required fields are marked *